- 您现在的位置：买卖IC网 > Sheet目录888 > UVK105CH4R3JW-F (Taiyo Yuden)CAP CER 4.3PF 50V 5% 0402
（2）Examples of good and bad solder application
Item
Not recommended
Lead wire of component
Recommended
Solder-resist
Mixed mounting of SMD and
leaded components
Chassis
Component placement close to
the chassis
Solder (for grounding)
Electrode pattern
Lead wire of component
Solder-resist
Hand-soldering of leaded
Soldering iron
Solder-resist
components near mounted
components
Solder-resist
Horizontal component
placement
◆Pattern configurations （Capacitor layout on PCBs）
1-1. The following is examples of good and bad capacitor layouts ; capacitors shall be located to minimize any
stresses from board warp or deflection.
possible mechanical
Items
Deflection of board
Not recommended
Recommended
Place the product at a right
angle to the direction of the
anticipated mechanical
stress.
1-2. The amount of mechanical stresses given will vary depending on capacitor layout. Please refer to diagram below.
E
D
Perforation
C
A
Slit
B
Magnitude of stress
A＞B＝C＞D＞E
1-3. When PCB is split, the amount of mechanical stress on the capacitors can vary according to the method used. The following methods
are listed in order from least stressful to most stressful: push-back, slit, V-grooving, and perforation. Thus, please consider the PCB,
split methods as well as chip location.
3. Mounting
◆Adjustment of mounting machine
1. When capacitors are mounted on PCB, excessive impact load shall not be imposed on them.
2. Maintenance and inspection of mounting machines shall be conducted periodically.
Precautions
◆Selection of Adhesives
1. When chips are attached on PCBs with adhesives prior to soldering, it may cause capacitor characteristics degradation unless the
following factors are appropriately checked : size of land patterns, type of adhesive, amount applied, hardening temperature and
hardening period. Therefore, please contact us for further information.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E02R01
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
UVK1J331MPD
CAP ALUM 330UF 63V 20% RADIAL
UVP1C470MED
CAP ALUM 47UF 16V 20% RADIAL
UVR2A221MHD
CAP ALUM 220UF 100V 20% RADIAL
UVY2C680MHD
CAP ALUM 68UF 160V 20% RADIAL
UVZ2A221MHD
CAP ALUM 220UF 100V 20% RADIAL
UWD1H560MCL1GS
CAP ALUM 56UF 50V 20% SMD
UWE-5/20-Q48NB-C
DC/DC CONVERT 5V 20A 1/8TH BRICK
UWF1E330MCL1GB
CAP ALUM 33UF 25V 20% SMD
相关代理商/技术参数
UVK105CH4R7JW-F
功能描述:多层陶瓷电容器MLCC - SMD/SMT CAP HI FREQ 0402 50V C0H 4.7pF 5%
RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
UVK105CH5R1JW-F
功能描述:多层陶瓷电容器MLCC - SMD/SMT CAP HI FREQ 0402 50V C0H 5.1pF 5%
RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
UVK105CH5R1JW-F
制造商:TAIYO YUDEN 功能描述:Ceramic Multilayer Capacitor
UVK1A102MDD
制造商:NICHICON 制造商全称:Nichicon corporation 功能描述:ALUMINUM ELECTROLYTIC CAPACITORS
UVK1A102MED
制造商:NICHICON 制造商全称:Nichicon corporation 功能描述:ALUMINUM ELECTROLYTIC CAPACITORS
UVK1A102MHD
制造商:NICHICON 制造商全称:Nichicon corporation 功能描述:ALUMINUM ELECTROLYTIC CAPACITORS
UVK1A102MPD
功能描述:铝质电解电容器 - 带引线 10volts 1000uF 10x12.5 ’20% 5LS RoHS:否 制造商:Kemet 引线类型: 电容:220 uF 容差:20 % 电压额定值:25 V 工作温度范围: 端接类型:Radial 外壳直径:8 mm 外壳长度:11 mm 引线间隔:5 mm 产品:General Purpose Electrolytic Capacitors 封装:Bulk
UVK1A102MPD1TD
制造商:Nichicon Corporation 功能描述:CAP ALUM 1000UF 10V 20% RADIAL